1.Overview
FBPC100 Series gives the interface conversion between G.703 E1 and V.35. This device provides an economical digital access solution for E1 and Fractional E1 network services. With a adapter cable, the Device can link to other DTE Device, such as router, at data rates of 64Kbps to 2048Kbps. User data is placed into the E1 frame, using only the required number of timeslots. Timeslot assignment is accomplished according to the Data Port speed and manual setting of DIP switches. FBPC100 Series is widely used in communication network, both in WAN and LAN connection field.

2.Features
Interface conversion between E1 and V.35
Support ITU-T V.35, G.703, G.704, G.823
Standalone and chassis module available, support hot-swap
Framed (N*64Kbps) and unframed (2.048Mbps) optional, support continuous and discontinuous timeslots setting
Frame mode support PCM30/ PCM31
CRC/non-CRC auto-negotiation on E1 interface
Support remote bandwidth control, and remote loop back under framed mode.
Support internal clock, E1 recovery clock or V.35 line clock
Provide local, diagnostic and remote loop back test.
For V.35 interface, DCE and DTE mode are optional
Comprehensive LED indicators on front panel, convenient for the diagnosis of equipment working state
16-slot, elaborate cooling design and two redundant power supply

3.Management
Support Console, WEB and SNMP management
Provide Timing Mode Setting, Loop back mode setting, Framed or Unframed mode setting clock resources selection, and etc.
Provide environment parameter monitoring, including power supply status and device operation temperature
Show details of system information, including Chassis name, location information, IP address, start-up time, software and hardware version
View & configure the working status of local and remote device, including connection status, port status
Provide user management to ensure the device operation security

4.Specifications
E1 ports
Compliant with: ITU-T G.703, G.704, G.823
Rate: 2.048Mbps
Code type: HDB3
Impedance: 75 ohm unbalanced & 120 ohm balanced optional
Physical connector: BNC for unbalanced & RJ45 for balanced

V.35 interface:
Compliant with V.35 standard
Rate: n×64Kbps, n=1~32
Physical connector: DB25 female jack
DCE & DTE optional

Power
Power supply:
AC Power: 100V-240V, 0.4-0.2A, 50-60 Hz
DC Power: -48V, 0.4A
Power consumption <2W

Environment
Operation Temperature: 0~50?
Operation Relative Humidity: 0~90%
Store Temperature: -20~65?
Store Relative Humidity: 0~95%

5.Oder Information
P/N               Description
F4-56A         Standalone Device, E1 to V.35 Converter, 220VAC Power input
F4-56D         Standalone Device, E1 to V.35 Converter, -48VDC Power input
F4-56M        E1 to V.35 Converter Module
FC-416         16 Slots Chassis, Supply two Powers
FC-416M      Management Module for the FC-416 Chassis

1.Overview
FBPC100 Series gives the interface conversion between G.703 E1 and V.35. This device provides an economical digital access solution for E1 and Fractional E1 network services. With a adapter cable, the Device can link to other DTE Device, such as router, at data rates of 64Kbps to 2048Kbps. User data is placed into the E1 frame, using only the required number of timeslots. Timeslot assignment is accomplished according to the Data Port speed and manual setting of DIP switches.FBPC100 Series is widely used in communication network, both in WAN and LAN connection field.

2.Features
Interface conversion between E1 and V.35, E1 and Ethernet
Support ITU-T V.35, G.703, G.704, G.823
Fully compatible with IEEE 802.3 and Ethernet Standards
Standalone and chassis module available, support hot-swap
Framed (N*64Kbps) and unframed (2.048Mbps) optional, support continuous and discontinuous timeslots setting
Ethernet port 10Mbps, Full/Half Duplex mode compatible
10Base-T LAN Interface on RJ-45 connector and MDI/MDI-X auto-crossover
Frame mode support PCM30/ PCM31
CRC/non-CRC auto-negotiation on E1 interface
Support remote bandwidth control, and remote loop back under framed mode.
Support internal clock, E1 recovery clock or V.35 line clock
Provide local, diagnostic and remote loop back test.
For E1 interface, 75 ohm (unbalanced) and 120 ohm (balanced) available and auto-negotiation.
For V.35 interface, DCE and DTE mode are optional
Comprehensive LED indicators on front panel, convenient for the diagnosis of equipment working state

3.Management
Support Console, WEB and SNMP management
Provide Timing Mode Setting, Loop back mode setting, Framed or Unframed mode setting clock resources selection, and etc.
Provide environment parameter monitoring, including power supply status and device operation temperature
Show details of system information, including Chassis name, location information, IP address, start-up time, software and hardware version
View & configure the working status of local and remote device, including connection status, port status
Provide user management to ensure the device operation security

4.Specifications
E1 ports
Compliant with: ITU-T G.703, G.704, G.823
Rate: 2.048Mbps
Code type: HDB3
Impedance: 75 ohm unbalanced & 120 ohm balanced optional
Physical connector: BNC for unbalanced & RJ45 for balanced

V.35 interface:
Compliant with V.35 standard
Rate: n×64Kbps, n=132
Physical connector: DB25 female jack
DCE & DTE optional

4.3Ethernet ports
Compliant with: IEEE802.3, 802.3u, 802.3x
Rate: 10Mbps, Half/Full auto-negotiation
Auto MDI/MDI-X
Physical connector: RJ45

4.4Environment
Operation Temperature: 0~50
Operation Relative Humidity: 0~90%
Store Temperature: -20~65
Store Relative Humidity: 0~95%

5.Oder Information
P/N                Description
F4-5516        V.35&Ethernet&FE1 to E1 protocol converter, V.35&Ethernet&FE1 share the 2Mbps bandwidth
FC-416         16 Slots Chassis, Supply two Powers
FC-416M      Management Module for the FC-416 Chassis

1.Overview

FBPC100 Series protocol converter is a high performance, remote, self-learning Ethernet Bridge. Its compact size and low cost make it ideal for cost-sensitive bridging applications or as a LAN extender over bit stream type infrastructures. The main E1 link may be clocked from the recovered receive clock or from an internal oscillator. This converter allows transmitting and receiving VLAN data packets. Standalone and Rack mount module are both available.

2.Features
Support transparent/ fractional E1 channel
Provide 10/100M electrical Ethernet port
Support bandwidth couple, loop test and two clock resources, etc
MDI/MDI-X auto-crossover, 10/100M auto-negotiation and speed limitation
AC220V and DC-48V power supply redundant

3.Management
Provide console management
Upgraded to SNMP/WEB management
View and configure the E1 and Ethernet ports status, such as E1 framed and unframed mode setting, E1 loop back, Ethernet ports rate limitation, and etc.
Provide environment parameter monitoring, including power supply status and device operation temperature
Provide user management to ensure the device operation security

3.Specifications
Power
AC Input: 100~240V
DC Input: -48V
Power Consumption:≤3W

E1 interface
Data rate: N×64Kbps, N=1~32
Code type: HDB3
Compliant with G.703, G.704, G.706 and G.823
75/120 optional
BNC (75ohm )/RJ45 (120ohm)
Transparent/ fractional optional
Qty: 1

Ethernet Interface
Standard: IEEE 802.3, 802.3u.
10/100M electrical port,
MDI/MDIX auto negotiation
Half/ full duplex
RJ45 connector
Qty: 1

3.Environment
Operation Temperature: 0~50
Operation Relative Humidity: 20~90%
Store Temperature: -20~65
Store Relative Humidity: 10~95%

4.Order Information
P/N                   Description
F4-51A             10/100M Ethernet over 1E1 converter, Standalone, AC220V power supply
F4-51D             10/100M Ethernet over 1E1 converter, Standalone, DC-48V power supply
F4-51M            10/100M Ethernet over 1E1 converter, Module card, AC220V/ DC-48V power

1.Overview
FBPC100 Series protocol converter is a high performance, remote, self-learning Ethernet Bridge. Its compact size and low cost make it ideal for cost-sensitive bridging applications or as a LAN extender over bit stream type infrastructures. The main E1 link may be clocked from the recovered receive clock or from an internal oscillator. This converter allows transmitting and receiving VLAN data packets. Standalone and Rack mount module are both available.

2.Features
Support transparent E1 channel
Provide 10/100M electrical Ethernet port
Support loop test, CRC selection, local/remote indicators etc.
Auto-detect the valid E1 channels and auto-balance the data flow among the valid E1 channels
MDI/MDI-X auto-crossover, 10/100M auto-negotiation and speed limitation
AC220V and DC-48V power supply redundant

3.Management
Provide console management
Upgraded to SNMP/WEB management
View and configure the E1 and Ethernet ports status, such as E1 loop back, Ethernet ports rate limitation, and etc.
Provide environment parameter monitoring, including power supply status and device operation temperature
Provide user management to ensure the device operation security

4Specifications
Power
AC Input: 100~240V
DC Input: -48V
Power Consumption: ≤15W

E1 interface
Data rate: 2.048Mbps
Code type: HDB3
Compliant with G.704, G.823
75/120 optional
BNC (75ohm)/RJ45 (120ohm)
Transparent E1 mode
Qty: 4/8/16

Ethernet Interface
Standard: IEEE 802.3, 802.3u.
10/100M electrical port, MDI/MDIX auto negotiation
Half/ full duplex
RJ45 connector

4.Environment
Operation Temperature: 0~50
Operation Relative Humidity: 20~90%
Store Temperature: -20~65
Store Relative Humidity: 10~95%

5.Order Information
P/N                                   Description
F5-4513A       10/100M Ethernet over 4E1 converter, Standalone, AC220V power supply
F5-4513D       10/100M Ethernet over 4E1 converter, Standalone, DC-48V power supply
F5-4513M       10/100M Ethernet over 4E1 converter, Module card, AC220V/ DC-48V power supply
F5-8513A       10/100M Ethernet over 8E1 converter, Standalone, AC220V power supply
F5-8513D       10/100M Ethernet over 8E1 converter, Standalone, DC-48V power supply
F5-8513M       10/100M Ethernet over 8E1 converter, Module card, AC220V/ DC-48V power supply
F5-16513A      10/100M Ethernet over 16E1 converter, Standalone, AC220V power supply
F5-16513D      10/100M Ethernet over 16E1 converter, Standalone, DC-48V power supply

1.Overview
FBOM1000 series Fiber Modem can modulate G.703 E1 signal or V.35 signal to single-mode or multimode fiber which extend the transmitting distance of E1 signal greatly. E1 signal support framed and unframed mode. When in framed mode, continuous or discontinuous time-slot can be selected. E1 fiber modem and V.35 fiber modem can be used together. Both of them are widely used in extending user interface in ATM or DDN.

.

2.Features
Realize E1 or V.35 signal transmitting over fiber; transmitting distance can reach 120Km without repeater
E1 interface: Framed & Unframed optional, 75 & 120ohm selectable
V.35 interface: support N×64K bit rate,DTE & DCE optional
Three loop back mode selectable: Local loop back, diagnostic loop back, remote loop back.
Provide bit-error test and time-slot follow by remote equipment, which brings a lot advantage in setting and debug
Multiple clock selection: Local clock, Fiber line clock, E1 recovery clock, V.35 line clock
Standalone and Chassis optional

3.Management
Support Console, WEB and SNMP management
Provide Timing Mode Setting, Loop back mode setting, Framed or Unframed mode setting clock resources selection, and etc.
Provide environment parameter monitoring, including power supply status and device operation temperature
Show details of system information, including Chassis name, location information, IP address, start-up time, software and hardware version
View & configure the working status of local and remote device, including connection status, port status

4.Specifications
Fiber interface
Rate: 4Mbps
Line code: 1B1C
Wavelength: 850nm/1310nm/1550nm
Connector: FC/SC/ST
Distance: 0-120Km

V.35 interface:
Compliant with V.35 standard
Rate: n×64Kbps, n=132
Physical connector: DB25 female jack
DCE & DTE optional

E1 interface
Compliant with ITU-T G.703, G.704, G.823
Rate: 2.048Mbps±50ppm
Impedance: 75 ohm unbalanced & 120 ohm balanced
Physical connector: BNC for unbalanced & RJ45 for balanced
Framed & unframed selectable
Support PCM30 & PCM31

4. Power
AC Input: 100~240V
DC Input: -48V

4.5 Environment
Operation Temperature: 0~50
Operation Relative Humidity: 0~90%
Store Temperature: -20~65
Store Relative Humidity: 0~95%

5.Oder Information
P/N                 Description
F9-E1             E1 fiber modem
F9-V.35         V.35 fiber modem
FC-416          16 Slots Chassis, Supply two Powers
FC-416M       Management Module for the FC-416 Chassis

1.Overview
PDH Multiplexer can multiplex 4/8/16E1,Ethernet (2*10/100Mbps) and V.35 signals in one fiber channel to transmit. It is suitable for low capacity, point-to-point application of remote transmission. The equipment is reliable, stable, easy to install and maintain, which can be monitored from Fi-view-MST management software. PDH Multiplexer is widely used in voice and data application field.

2.Features
Providing up to 16E1,2 10/100Mbps Ethernet and 1 V.35 channel
Ethernet port support VLAN and flow control
Support the local/remote E1 loop back
For V.35 channel, framed and unframed mode optional.
Support internal clock, E1 recovery clock or V.35 line clock.
Providing an RS232/RS485 asynchronous interface optional
Complete alarm functions
Standalone and rack mount module optional
100-240VAC and -48VDC optional

3.Management
Support local and remote management
Support Console, WEB and SNMP management
Show details of system information, including Chassis name, location information, IP address, start-up time, software and hardware version
View & configure the working status of local and remote device, including connection status, speed, half/full duplex mode, port status
Real-time alarm monitor and history alarm management are both available
Online firmware updating

4.Specifications
Optical Port
Rate: 150Mb/s+/-50ppm
Wavelength: 1310nm/1550nm
Sensitivity: Better than -36dB
Connector: FC/SC/ST

E1 Port
Rate: 2048Kbps
Code type: HDB3
Compliant with G.703, G.704
Impedance: 75 ohm unbalanced & 120 ohm balanced
Physical connector: BNC for unbalanced & RJ45 for balanced
Unframed mode
Numbers: 4-8

Ethernet ports
Compliant with: IEEE802.3
Rate: 10/100Mbps
Full/Half duplex auto-negotiation
Physical connector: RJ45
MDI/MDI-x auto-negotiation
Ethernet port: 2-switch ports

V.35 Port
Compliant with V.35 standard
Data rate: 2048Kbps or N*64Kbps, N =1~31
Operation mode: DTE/DCE optional
PCM30/PCM31 optional
Three kinds of loop back mode
Physical connector: DB25 female jack
Numbers: 1

Operating Environment
Temperature: 0~50?
Relative Humidity: 20~90%

6.Order Information
F9-240-04FA         8E1 port Multiplexer, 75&120ohm both OK, Optical port: distance:40km, FC/PC, SM1310nm, Standalone, 220VAC power supply
F9-240-04F23A      8E1 port Multiplexer, 75&120ohm both OK, 2-port 10/100Mbps line-speed Ethernet. Optical port: distance:40km, FC/PC, SM1310nm, Standalone, 220VAC power supply
F9-240-04FD         8E1 port Multiplexer, 75&120ohm both OK, Optical port: distance:40km, FC/PC, SM1310nm, Standalone, -48VDC power supply
F9-240-04F23D      8E1 port Multiplexer, 75&120ohm both OK, 2-port 10/100Mbps line-speed Ethernet. Optical port: distance:40km, FC/PC, SM1310nm, Standalone, -48VDC power supply

1.Overview
PDH Multiplexer can multiplex 4/8/16E1,Ethernet (2*10/100Mbps) and V.35 signals in one fiber channel to transmit. It is suitable for low capacity, point-to-point application of remote transmission. The equipment is reliable, stable, easy to install and maintain, which can be monitored from Fi-view-MST management software. PDH Multiplexer is widely used in voice and data application field.

2.Features
Providing up to 16E1,2 10/100Mbps Ethernet and 1 V.35 channel
Ethernet port support VLAN and flow control
Support the local/remote E1 loop back
For V.35 channel, framed and unframed mode optional.
Support internal clock, E1 recovery clock or V.35 line clock.
Providing an RS232/RS485 asynchronous interface optional
Complete alarm functions
Standalone and rack mount module optional
100-240VAC and -48VDC optional

3.Management
Support local and remote management
Support Console, WEB and SNMP management
Show details of system information, including Chassis name, location information, IP address, start-up time, software and hardware version
View & configure the working status of local and remote device, including connection status, speed, half/full duplex mode, port status
Real-time alarm monitor and history alarm management are both available
Online firmware updating

4.Specifications
Optical Port
Rate: 150Mb/s+/-50ppm
Wavelength: 1310nm/1550nm
Sensitivity: Better than -36dB
Connector: FC/SC/ST

E1 Port
Rate: 2048Kbps
Code type: HDB3
Compliant with G.703, G.704
Impedance: 75 ohm unbalanced & 120 ohm balanced
Physical connector: BNC for unbalanced & RJ45 for balanced
Unframed mode
Numbers: 4

Ethernet ports
Compliant with: IEEE802.3
Rate: 10/100Mbps
Full/Half duplex auto-negotiation
Physical connector: RJ45
MDI/MDI-x auto-negotiation
Ethernet port: 2-switch ports

V.35 Port
Compliant with V.35 standard
Data rate: 2048Kbps or N*64Kbps, N =1~31
Operation mode: DTE/DCE optional
PCM30/PCM31 optional
Three kinds of loop back mode
Physical connector: DB25 female jack
Numbers: 1

Operating Environment
Temperature: 0~50?
Relative Humidity: 20~90%

5.Order Information
F9-120-04FA         4E1 port Multiplexer, 75&120ohm both OK, Optical port: distance:40km, FC/PC, SM1310nm, Standalone, 220VAC power supply
F9-120-04F23A      4E1 port Multiplexer, 75&120ohm both OK, 2-port 10/100Mbps line-speed Ethernet. Optical port: distance:40km, FC/PC, SM1310nm, Standalone, 220VAC power supply
F9-120-04FD         4E1 port Multiplexer, 75&120ohm both OK, Optical port: distance:40km, FC/PC, SM1310nm, Standalone, -48VDC power supply
F9-120-04F23D      4E1 port Multiplexer, 75&120ohm both OK, 2-port 10/100Mbps line-speed Ethernet. Optical port: distance:40km, FC/PC, SM1310nm, Standalone, -48VDC power supply

1.Overview
PDH Multiplexer can multiplex 4/8/16E1,Ethernet (2*10/100Mbps) and V.35 signals in one fiber channel to transmit. It is suitable for low capacity, point-to-point application of remote transmission. The equipment is reliable, stable, easy to install and maintain, which can be monitored from Fi-view-MST management software. PDH Multiplexer is widely used in voice and data application field.

2.Features
Providing up to 16E1,2 10/100Mbps Ethernet and 1 V.35 channel
Ethernet port support VLAN and flow control
Support the local/remote E1 loop back
For V.35 channel, framed and unframed mode optional.
Support internal clock, E1 recovery clock or V.35 line clock.
Providing an RS232/RS485 asynchronous interface optional
Complete alarm functions
Standalone and rack mount module optional
100-240VAC and -48VDC optional

3.Management
Support local and remote management
Support Console, WEB and SNMP management
Show details of system information, including Chassis name, location information, IP address, start-up time, software and hardware version
View & configure the working status of local and remote device, including connection status, speed, half/full duplex mode, port status
Real-time alarm monitor and history alarm management are both available
Online firmware updating

4.Specifications
4.1 Optical Port
Rate: 150Mb/s+/-50ppm
Wavelength: 1310nm/1550nm
Sensitivity: Better than -36dB
Connector: FC/SC/ST

E1 Port
Rate: 2048Kbps
Code type: HDB3
Compliant with G.703, G.704
Impedance: 75 ohm unbalanced & 120 ohm balanced
Physical connector: BNC for unbalanced & RJ45 for balanced
Unframed mode
Numbers: 4-8-16

Ethernet ports
Compliant with: IEEE802.3
Rate: 10/100Mbps
Full/Half duplex auto-negotiation
Physical connector: RJ45
MDI/MDI-x auto-negotiation
Ethernet port: 2-switch ports

V.35 Port
Compliant with V.35 standard
Data rate: 2048Kbps or N*64Kbps, N =1~31
Operation mode: DTE/DCE optional
PCM30/PCM31 optional
Three kinds of loop back mode
Physical connector: DB25 female jack
Numbers: 1

Operating Environment
Temperature: 0~50?
Relative Humidity: 20~90%

5.Order Information
F9-480-04FA         16E1 port Multiplexer, 75&120ohm both OK, Optical port: distance:40km, FC/PC, SM1310nm, Standalone, 220VAC power supply
F9-480-04F23A      16E1 port Multiplexer, 75&120ohm both OK, 2-port 10/100Mbps line-speed Ethernet. Optical port: distance:40km, FC/PC, SM1310nm, Standalone, 220VAC power supply
F9-480-04FD         16E1 port Multiplexer, 75&120ohm both OK, Optical port: distance:40km, FC/PC, SM1310nm, Standalone, -48VDC power supply
F9-480-04F23D      16E1 port Multiplexer, 75&120ohm both OK, 2-port 10/100Mbps line-speed Ethernet. Optical port: distance:40km, FC/PC, SM1310nm, Standalone, -48VDC power supply

1.Overview
Fibridge E1 PDH Multiplexer can combine up to 16E1 and 4-ports Ethernet (10/100Mbps line speed) signals in one fiber channel to transmit. It is suitable for low capacity, point-to-point application of remote transmission. The circuit part of the equipmentis fully digitized. The whole equipment is reliable, stable, easy to install and maintain. It has good temperature and voltage characteristics, complete alarm functions, one RS232 asynchronous interface and remote loop back functions(from software). The 12-slot chassis FC-912 expand the number of the ports and and be managed by the management system Fi-view-MP in SNMP/WEB/Console mode.

2.Hardware Feature
6U height, up to 12 slots, 24 optical channels
Compatible with 4E1 8E1 16E1 PDH Multiplexer
management card supports hot-swap plug
Management card have one RS232 port for console management, and one RJ45 port for SNMP&WEB management
DC-48V power supply, 220VAC is optional

3.Software Feature
Monitor the port''''s status of optical port & E1 port & ethernet of local & remote device
Set Local/Remote loop
Set Alarm Sound enable/disable
realtime alarm message popup
History alarm message mangement
User Management

 
4.Order Information
FC-912 12-slot PDH Multiplexer Chassis
FC-912-M Management Card of FC-912
FP-9075A 75W AC220VAC Power Supply Module